Linovision EOC-Converter is a combination of Power over Coax (PoC) and Ethernet over Coax (EOC) converter. With proprietary ePOE technology, it is designed to transmit both PoE power and ethernet data over coaxial cables or twisted pair cables, including siamese cable, CATV cable, power cable, Cat5E/Cat6, etc. The max transmission distance can be 3,300ft. It is super useful to upgrade the analog camera system to an IP surveillance system without replacing legacy coaxial cables. It can also be used in elevators to get power and network from coax or twisted pair cables.
Industrial design, with built-in heat sink Ensure super reliability and hassle-free transmission.
It can Provide power to remote POE device with max. 30W and no local DC power adapter is required. （Note: The POE OUT Port only support PoE Mode A）
Compatible to IEEE802.3af/IEEE802.3at POE protocol, max21W POE load capacity in 100m(330ft), or 11W POE load capacity in 300m(1000ft).
DIN-Rail Installation. Plug-and-play, configuration free, makes installation simplest. Small design (3.1"x2.0"x0.9") and light weight.
Upgrade traditional analogue video surveillance system to IP surveillance system with existing coaxial cable at max 3,000ft distance.Up to100Mbps bandwidth over 1,000 feet regular coax cable transmission, working with CCA/CCU RG59/RG6 cable
There are some locations that are without network cables but still need POE power and data transmission, for example, elevator carts in many buildings, or doorbell cables, LINOVISION EOC converters are perfect for this application. It can transmit POE power and IP data over coax RG59 cable, twisted pair cable, doorbell cable, telephone cable, or even power cables. The remote-connected device can be IP cameras, IP Video intercoms, IP phones, IP controllers, etc.
For many elevators there are no ethernet cables and no camera powers in the elevator cart, LINOVISION EOC converters are perfect for this application. It can transmit POE power and IP data over coaxial or twist pair cables. One passive EOC-transmitter will be put inside the elevator cart to feed the camera or signal board, and one EOC-receiver will be in the control room, powered by POE switch/POE injector/POE NVR. For multiple elevators application, one EOC-Switch08 or EOC-Switch24 will be put in the control room, working together with max 8 elevators.
Comparison between LINOVISION EOC and similar products
|
|
|
|
|
|
|---|---|---|---|---|---|
| Model | EOC-Converter | MoCA Adapter | GCA-6000KITb | Ve***ty VHW-HWPS-B/C | A**S T8640 |
| Transimit POE | ✔ | NO(ethernet only) | NO(ethernet only) | ✔ | ✔ |
| Transmission Distance | 3000ft | 300ft | 2600ft | 1000ft or 1600ft with power supply | 1000ft |
| Without extra DC power | ✔ | / | / | Optional | ✔ |
| Price | $ | $ | $ | $$$ | $$$$ |
Use good quality IEEE802.3at 30W PoE switch to provide POE power to our EOC-Receiver, preferred with the DC53V input voltage, instead of regular 48V input voltage. Please also check the PoE budget of the PoE Switch, and make sure that the port individually can output 30W PoE power. (Most PoE Switches in the market do not support all ports at 30W POE output). Use point-to-point direct coaxial cable. The cable and connector quality will heavily affect the transmission distance. Please make sure to connect EOC-Receiver to the POE switch, and then connect the PoE cameras to the EOC-Transmitter side. The PoE output from the EOC-Transmitter is PoE mode A (use Pin 1,2,3, 6 for both data and power). If your PoE device is PoE mode B, please use our POE-Splitter or PoE-Extender02. The PoE output is standard IEEE802.3af/at PoE, and not compatible with 24V passive PoE devices.
Linovision EOC-Converter’s advantages over other products in the market.
Linovision EOC-Converter VS Motorola MoCA Adapter or StarTech EOC1110K
Linovision EOC-Converter can transmit both PoE power and ethernet data, while MoCA adapter does not support.
Linovision EOC-Converter VS Axis T8640 or Veracity Highwire Powerstar or DUALCOMM DECA-200
Quite similar, but Linovision EOC-Converter can transmit PoE and data up to 3,300ft distance, while others is 1,000ft.
Linovision EOC-Converter VS Altronix eBridge1PCRMT
Quite similar, but Linovision EOC-Converter can transmit PoE and data up to 3,300ft distance, while Altronix eBridge is 1,640ft.
Linovision EOC-Converter VS Enconn Mini-Power
Quite similar, but Linovision EOC-Converter can transmit PoE and data up to 3,300ft distance, while Enconn is only 800ft.
| Model | EOC-Converter (Receiver+Transmitter) |
|---|---|
| Function Port | 1*10/100 Mbps Base-TX 1*BNC |
| Power Consumption | <2W |
| Transmission Bandwidth | RG59 coaxial cable: 400m/100Mbps, 1000m/10Mbps |
| PoE Protocol (EOC-Receiver) | work as a PoE Powered device, compliant to IEEE802.3af/at. Auto adaptive to PoE mode A and B from PSU (PoE Switch or PoE NVR, strongly recommend to use 30W PoE+ port) |
| PoE Protocol (EOC-Transmitter) | work as a PSU, provide PoE power to standard IEEE802.3af/at PoE device (48V Passive PoE, Pairs 1, 2+; 3, 6 Return) |
| Network Standard | IEEE802.3, IEEE802.3u, IEEE802.3x |
| Lightning Protection | Common Mode 4KV Differential Mode 2KV |
| Operating Temperature | –30°C to 65°C (–22°F to 149 °F ) |
| Operating Humidity | 5%–95% |
| Dimension (each) WxDxH | 79mm×52mmx23mm (3.1" x 2.0" x 0.9") |
| Weight (each) | 61g (0.134lbs) |
It can transmitter ethernet data and POE power over coaxial cables, twist pair cables, power cables, video cables or almost any two-pin cables.
Yes, one pair of EOC converter can be used to transmit multiple device over single coaxial cable with NVR/POE switch/WI-FI AP. The connection will be multiple device -> NVR/POE switch/WI-FI AP -> EOC Transmitter -> Coaxial cable ->EOC Receiver -> POE NVR/POE Switch/POE Injector with internet. Please note that the EOC receiver has to be connected to an POE NVR or POE Switch to be powered.
Yes. But you need a POE injector in EOC receiver side to provide power to EOC receiver and EOC transmitter. It is recommended to use 56V 30W POE injector.
The maximum load capacity is 21W in 300ft transmission which is sufficient to power a regular IP PTZ camera. The load capacity can be at least 11W in 1000ft transmission which is sufficient to power most of IP cameras.
The maximum transmission distance is 3000ft. Please note that the load capacity will drop down to 4W with general DC48V injector, so it’s recommended to use 60W or 75W poe injector in the receiver side.
It can work with POE devices like IP cameras, POE Wi-Fi AP, VoIP phones, etc. And it can also work with non-POE device like PC/NVR, etc. And you still need a power injector to power the EOC receiver side even though don’t need poe.
It supports IEEE802.3af and IEEE802.3at standard. It can work with most of the IP cameras and mini PTZs in the market, we also have customers use this to power POE WIFI AP and it is working well.
It supports DIN Rail installation(Standard 35mm din rail), or you can put it inside a regular camera’s junction box, since it is very small in dimension, that is 3.1” x 2.0” x 0.9”
Several main reasons are as follow: 1. EOC transmitter has to be connected to POE device (IPC/VoIP), and EOC receiver is connected to POE supply device (POE NVR, POESwitch or POE Injector). The reverse connection will not work. 2. It is used for point-to-point coax cable direct connection only, no BNC repeater/T-connect/splitter in the middle. 3. It may be caused by insufficient load capacity. The maximum load capacity is 21W in 300ft transmission which is sufficient to power a regular IP PTZ camera. The load capacity can be at least 11W in 1000ft transmission which is sufficient to power most of IP cameras or VoIP phones. 4. No power supply will also make it fail to work. Please be informed that EOC receiver has to be connected to an POE NVR, POE Switch or POE Injector to be powered.
Saved me from running cat5 through buried conduit, along with exceeding ethernet distance limitations.
Works well with a cheap TP-Link Tapo C320WS and 5v PoE Splitter. Time will tell how long it lasts in a outdoors waterproof box. No issues streaming continuously over a week at 2K 15fps quality.
This little device right here is great simple plug-and-play works like a charm, very compact, and I love that they’ve incorporated rackmount clips
I have replaced 48 cameras and change them to POE. 6 of them were impossible to replace cables, because they are under ground, that is why I had to use this device to use POE camera. I wasn't sure at the first time, because to good to be true. At first I installed three of them about one month ago, and they where working fine, with good 4K quality. I realized the two of them randomly turning off, but one of them always turned off. with lot of troubleshooting, I found out that specific one had a bad BNC connection. I changed the BNC head, now they working perfectly. Remember to make a good BNC head, otherwise you will have problem on all of them, if they are in the same network. Anyway I bought 3 more, and installed them outside into LINOVISION EOC Converter Waterproof Box. They are working fine for now, lets see if in raining days or in the hot summer will be good too. cross our fingers. the quality of unit by itself is very good, well made.
We have these on 7 of our IP cameras, they work great. No problems at all.
I’m coming up on about one year and I used these for a brand new IP camera installation with 30 total cameras using all old 20-year-old BNC cabling.
So far so good and these things saved an enormous amount of time, and not to mention I was able to get the job only because I said my company would use the existing old BNC cable in the building and not need to tear into the walls and run new Cat6 cabling for all 30 cameras.
There’s just not much history to go by with these devices so when I say they’ve been running for almost a year, I don’t know that there is any other commenters on here that have used them for longer than one year.
If I got five years out of them, I would be thrilled. That being said my company did save about $7000-$10,000 not having to pay for low-voltage installers to run each cable.
Introduction au convertisseur EOC (3,3 Mo)
